How To Repair Drywall After Removing Backsplash Tile

Well, folks. It's calendar week two and I take to say I'thousand already feeling the pressure. Our eclectic master bath revamp is underway but it feels like we oasis't made much progress. Here'southward the plan if y'all missed final calendar week's post. Take a await at that pretty earlier you lot see the ugly that happened this week when nosotros learned how to remove backsplash tile and replace drywall.

Make sure you lot take some time to go look at the progress of all of the participants over on the Ane Room Challenge site. I recall seeing the process of design and remodel really brings things back downward to reality. This isn't like a home show where yous don't e'er see the nitty gritty and the "oops" moments.

If y'all're new here, welcome! I'm so glad to have you here to be a function of this little journey I'thousand on to continue making houses into homes. You lot can learn more here about Rufus & Henrietta and me in general.

So back to the master bathroom. Ane of the start things we needed to do was remove backsplash tile as nosotros will be replacing the wearisome old travertine with some really pretty white subway that looks handmade.

What You'll Need to Remove Tile:

• Prybar
• Putty knife
• Rubber mallet
• Optional merely highly recommended: a stiff drink

As you can meet, we had quite the array of tools only the ones listed above did the play tricks almost efficiently. Ok, here's my disclaimer. If you are removing stone tiles like we were and you are able to not break into the drywall, I will choreograph a customized jig to celebrate y'all. I honestly don't think there is a way around it.

We started off being extremely conscientious and then soon realized, there was no going back. To start chipping abroad at the tile, we began with the prybar and rubber mallet. Start chipping away at the grout lines, starting time with the tiles at the end. Then, using your putty knife and rubber mallet, you can become further backside the tile and also break the caulk lines.

Yous want to exist somewhat careful, merely y'all'll likely soon realize that the sparse set used to install this stone tile is then strong, you'll hulk the drywall right out with the tile. Once all of the tile is removed, unscrew any exposed drywall screws.

Just look at that picture …. ahhhh … I know y'all just took a deep sigh of … Are you lot kidding me? This is when I went to full panic style. Just not to worry, I did a lilliputian research and soon felt ok about this disastrous state of our bathroom. Then now, the tiles are gone and the screws are removed. Next, we'll talk nearly repairing the drywall.

In this situation, you can meet it was beyond just a elementary patch job. We had to pull out the big guns for this project.

What Yous'll Need to Supersede Drywall:

• 2′ ten 2′ drywall pieces (unless you lot want a gigantic 8′ or 12′ slice)
• Heavy duty box cutter
• Pencil
• Chisel
• Prophylactic mallet
• Direct edge / one thousand stick
• Drill (impact commuter recommended)
• 1 1/4″ screws

And so at present nosotros have to clean this mess up a little to piece of work on giving united states of america a fresh new offset with some new drywall. Effort to remove as much of the debris as you tin from the tile removal.

Next, describe a line with a pencil for where you'd like your clean cut to be. Keep in mind that you desire to make the cut big enough to achieve a stud on both sides. This could mean you lot have to cut further than you'd initially planned, but you demand the studs to screw in the drywall. Without that, yous would have drywall just floating at that place and any tile/pictures/etc. you hang on the wall in the future could fall correct off.

One time you have your straight pencil guide on the wall, you lot can starting time to bit away at the drywall. I found information technology easier to score along the line with the box pocketknife first.

In one case information technology was scored, I came back in with the chisel and rubber mallet. Our chisels have one side that is flat and one side that is beveled. The flat side, you wall want to go along on the outside of your hole to make as clean of a break every bit possible.

Slowly chisel around your make clean line and then work your fashion in as you remove the old drywall. After that'south all removed, relish a sip of that drinkable considering things are starting to look upwards.

Now to kickoff putting upwardly the new drywall. You lot will want to cutting the new pieces so they volition fit over half of the exposed studs. And then if you lot have ii pieces, you want to make sure they see at the center of the stud so you can screw both pieces in securely.

To cutting the drywall, first measure twice and then make a direct pencil line. Score forth that line with a box knife.

So, stand the drywall upwards and lightly brand a cut through to the other side, cutting the backing paper as yous become. Practise this on each side. I found information technology was easier to make a clean interruption if I scored on both sides. If I didn't score the back, the paper started to pull off and the drywall became harder to work with and weaker.

Once both sides are scored, you should be able to curve up the piece yous are cutting and it volition snap at the line you scored.

To make sure you have a tight fit to the wall, you might accept to make clean upwardly some edges with either the chisel or the box knife. Screw the new pieces to the studs and there you have it.

At that place are nevertheless a lot of to-dos on our list but at least nosotros're making headway. Side by side week, we'll discuss mudding and whatever else will come with the next steps in our program. Thanks to non having holes in the wall anymore!

(Update: Y'all can see the reveal here )

Happy Creating!

And in instance you need something pretty to wait at:

Source: https://rufusandhenrietta.com/how-to-remove-tile-and-replace-drywall/

Posted by: harrisdreatenty.blogspot.com

Share this post